UnoFin Acrylic Texture

Ready to use synthetic-mineral render for waterproofing and decoration of façades and internal walls. Internal or external use. On walls and ceilings. Decorative finish for WalAce SYSTEM (EIFS).

Download technical data sheet

Additional information

Composition

Product based on acrylic resins, mineral aggregate and pigments and organic and inorganic additives.

Features and applications

Antimould, anti algae.
Waterproof.
Permeable to water vapour, allowing the substrate to breathe.
Fast and simple application.
Floated, drop and flat drop finishings.
Compatible with most substrates.
Resistant to weathering, UV light and industrial atmosphere.
Excellent adherence on usual contruction substrates.
Washable.
Product with protection from fungal, mould and algae contamination that achieves a preventive and retardant effect lasting but not permanent.
The duration of this affection depends on the exposure to humidity and the concentration of spores in the area, which make the conditions especially favorable for the growth of microorganisms, therefore periodic preventive maintenance treatment is recommended

Substrates

Compatible with mortars, concrete, one coat mortars, gypsum, gypsum board and old painted substrates.
It is not compatible with fresh lime coatings, resin or polish, or with tempera, lime or silicate paint.
Substrates must be clean sound and free of dust, oil, paint, loose particles, etc.
Decorative finish for the WalAce SYSTEM (EIFS).
Use consolidating primer on low cohesion substrates. Allways prime with UnoFin Acrylic BASECOAT.

Instructions for use

Stir until material is homogeneous.
The product is ready mixed for trowel application. Until 250 ml of water per buckets can be added to adjust workability. For spray gun, up to 1 litre per 25 kg buckets may be added.
For a drop finish use a spray gun or a steel trowel . Float the surface when its consistency is adequate.
May be floated justs after application depending on weather conditions. Application's thickness from 1 to 3 mm.
Clean tools with water inmediately after use. Stains can be removed with paint thinner.

Cautions and recommendations

Do not apply at temperatures below 5ºC or above 35ºC, under direct sunlight, rain or risk of frost.
Do not apply on horizontal substrates (floors) or sloped less than 45º.
Protect the upper part of the render to avoid rain water penetration.
To avoid small colour variations order all the necessary product in a single order and do not mix different batch numbers in a single working area.
When using spray gun keep pressure, and wall distance constants to avoid finishing variations. (If necessary, apply several coats until coverage and minimum thickness are obtained).
Protect surrounding areas thoroughly. Clean with water any spillage before dryng.

Packaging

UnoFin ACRYLIC TEXTURE comes in 25 kg plastic buckets.
Shelf life: 2 years in sealed original packaging, store in fresh and dry places. Avoid exposure to temperatures below 5ºC or above 30ºC. Sheltered from weather conditions.

Technical data

(Statistical data obtained under standard conditions)

Viscosity	400 dPas±100
Specific weight	1,8 g/cm³
Yield	2 a 3 Kg/m² (2 mm layer)
Adherence	> 15 Kg/cm² (concrete)
Drying time	30 min at 25ºC and 50% RH
Colours	Check range
Water absorption (EN 15824)	Low (W3)
Water vapor permeability (EN 15824)	Medium Sd (≥0.14 y <1.4)
Thermal conduction (EN 15824)	0,83-0,93 W/mK
Reaction to fire (EN 13501)	A2-S1,d0

Note

The instructions for use are given according to our tests and knowledge and do not imply any commitment by PIDILITE GRUPO PUMA nor free the consumer from the examination and verification of the products for their correct use. Claims must be accompanied by the original packaging to allow a proper traceability.

PIDILITE GRUPO PUMA is not responsible, in any case, for the application of its products or constructive solutions carried out by the application company or other parties involved in the process and / or execution of the work, limiting the responsibility of PIDILITE GRUPO PUMA exclusively to the damages directly attributable to the supplied products, individually or integrated in systems, due to failures in their manufacturing process.

In any case, the drafter of the work project, the technical management or the person responsible for the work, or collaterally the application company or other parties involved in the process and / or execution of the work, must ensure the suitability of the products addressing the characteristics of them, as well as the conditions, support and possible pathologies of the work in question.

The values obtained by PIDILITE GRUPO PUMA's products or its constructive solutions that, as the case may be, are determined by the EN standards or any other regulation that applies to it in each case refers exclusively to the conditions specifically stipulated in said regulation and that are referred to, among others, to certain characteristics of the support, humidity and temperature conditions, etc. without being them required in the tests obtained under different conditions, all in accordance with the relevant regulation.