Paviland^® Solera R Autonivelante

Technical Caracteristics

Product based on cement, selected aggregates, synthetic resins, fibres, and additives.

Advantages and Uses

• Great levelling capacity.
• Interior floors: bonded up to 50 mm and unbonded screeds for thicknesses between 50 and 100mm Suitable for underfloor heating.
• Effortless application due to its high fluidity and excellent flatness. 
• Rapid commissioning.
• Particularly suitable for use in cold weather conditions, where normal-drying flowing screeds require longer before being commissioned.

Suitable Substrates

• Substrates must be resistant enough, stable, sound  and clean. Free of dust, release agents, organic products, etc.
• Prior to the application of PAVILAND SOLERA R AUTONIVELANTE, any honeycombs and/or cracks present in the substrate must be properly repaired using right products from our Paviland or Morcemrest range.
• Bonded screeds (thicknesses below 50 mm) on sound concrete substrates, the PAVILAND PRIMER R primer must be applied beforehand. For other types of substrates (ceramic, marble, etc.), please consult our technical department.
• Unbonded screeds: thicknesses between 50 and 100 mm on insulating substrates, plastic membranes, or vapour barriers. For other type of substrates, please consult our Technical Department.

Application Procedure

• Define and mark the maximum level of the screed.
• The pouring area should be set up to prevent sections with different setting times. To achieve this, consider the available resources for the job, environmental conditions, and the mortar's open time. 
• Pre-confining pouring areas can also help create partition joints, avoiding the need for later cutting. 
• Mix the product with water (4.0 -4.5 litres per 25 kg bag) with a mechanical mixer at low speed (500 rpm approximately) until getting an homogeneous paste without lumps. The exact water dosage is particularly important to avoid product segregation, increased shrinkage, and reduction of strength. 
• Let the paste rest around 2 min.
• For large areas, it is recommended to pump the mortar using twin-spiral mixers capable of delivering 20–40 L/min. This procedure helps to optimise installation times.
• Spread manually using a metal levelling trowel once the primer has hardened. Then pass a nylon spiked roller of an adapted size to the thickness of the screed.
• Respect structural joints and create perimeter and partition joints.
   

Recommendations

• Do not apply the product under temperatures of 5º nor above 30º.
• Do not apply if there is risk of frost, rain, heavy wind, or under direct sun light. 
• Do not apply outdoor.
• Do not apply on moisten floors or at risk of having moisture.
• Keep in mind the product's pot life when planning the tasks. 
• Use gloves and protective goggles when manipulating the product. Keep away from children. Do not add sand, cement, or any other material that may alter the original formulation.
• Once the product has been mixed, and its resting time has elapsed, do not add any water.
• For floors with surfaces to be covered larger than 20 m² or more than 10 linear meters, it is recommended to create expansion joints, dividing sections, with joints of about 6 mm that can be filled with PUMALASTIC MS or PU.
• The expansion joints of the original substrate must be respected, and perimeter joints should be created.
• The surface layer should be protected from an extremely fast drying, specially under elevated temperatures or / and heavy winds.
• Before applying the final floor, residual moisten of the screed should be previously checked to make sure it is suitable for it 
• Paviland Solera R Self-Levelling must be protected by discontinuous coverings.

Packaging and Storage

Technical data

(Statistical results obtained under standard conditions)

(*): Timings are given according to temperature of 23ºC and 55% relative humidity. Periods of time will be shorter at higher temperatures and longer at lower temperatures.

CE Mark

GRUPO PUMA ESPAÑA, S.L Avda. AGRUPACIÓN CÓRDOBA, Núm. 17 14014 CÓRDOBA 26
PPAVILAND SOLERA R AUTONIVELANTE Nº: 501869-01 EN 13813 CT C25 F5 B1 5 type, fast-setting, self-levelling, screed mortar for interior floors, until 50 mm thickness when adhered and until 100 mm when non-adhered.
Reaction to fire	Class A1
Hazardous substances emission	CT
Compressive strength.	C25
Resistance to bending	F5
Tensile strength	B1,5
Hazardous substances	See safety datasheet

Environmental Product Declaration (EPD)

Cement based mortar prepared with aggregates that are supplied close to the production center, which reduces the greenhouse gas emissions that would otherwise arise from their transport. Manufactured in production centers with an Environmental management certified system following ISO 14001 regulation, offering a firm promise of sustainability and respect for the environment. Cement based mortar with type III ecological label (the most strict) Environmental Product Declaration verified externally by AENOR.

Notas

The instructions for use are given according to our tests and knowledge and do not imply any commitment by GRUPO PUMA nor free the consumer from the examination and verification of the products for their correct use. Claims must be accompanied by the original packaging to allow a proper traceability.

GRUPO PUMA is not responsible, in any case, for the application of its products or constructive solutions carried out by the application company or other parties involved in the process and / or execution of the work, limiting the responsibility of GRUPO PUMA exclusively to the damages directly attributable to the supplied products, individually or integrated in systems, due to failures in their manufacturing process.

In any case, the drafter of the work project, the technical management or the person responsible for the work, or collaterally the application company or other parties involved in the process and / or execution of the work, must ensure the suitability of the products addressing the characteristics of them, as well as the conditions, support and possible pathologies of the work in question.

The values obtained by GRUPO PUMAS's products or its constructive solutions that, as the case may be, are determined by the EN standards or any other regulation that applies to it in each case refers exclusively to the conditions specifically stipulated in said regulation and that are referred to, among others, to certain characteristics of the support, humidity and temperature conditions, etc. without being them required in the tests obtained under different conditions, all in accordance with the relevant regulation.